Go
New
Find
Notify
Tools
Reply
  
-star Rating Rate It!  Login/Join 
Tom
Posted
Over the years we have discussed shoulder clods and rolls.

They are great for chopped/pulled/sliced beef.

Often used by Texas caterers,instead of brisket.

Danny Gaulden has tested many products and techniques over the years and been gracious enough to share the results.

He has also had a Cookshack to work with.

Danny Gaulden
BBQ List
Shoulder Clod
8/6/01

Boys & Girls,

Here's the report on the #114 clod shoulder clod:

Raw weight: 20.3 lbs.

After Cooked Wt: 11.5 lbs. (57% yield, 43% shrinkage).

Actual yield for Serving Table after cooked and trimmed of fat...9.6 lbs. (47%).

Cooking temperatures: 225-250 degrees with a couple of short term spikes to 265.

Cooking Time: 14 hours, 15 min.

Internal temperature when pulled from pit: 180 degrees.

The clod was very tender and moist. I used my Forschner roast beef knive to slice it. A sharp knife is a must to slice this cut of beef when cooked to the tender stage. The connective tissue that connects the two large muscle groups were very tender and not offensive.

This cut of beef reminds me of a bottom round and chuck roast combination, for it has a few stringy sections as well as a lot of solid packed, non stringy sections. It taste more like a roast, even though it was smoked for a long time and under constant smoke most of the time. However, it had a wonderful rich beefy flavor.

The down side to me is that it is so thick that good smoke penetration way down deep is not possible. Cutting it in half would probably contribute greatly to the smoke flavor, and I don't think any ill effects would occur from doing this.

Make sure you have a good pair of heat resistant gloves when removing this large cut of meat from your smoker, or a very large spatula to slip under it. A pizza peel would work great.
 
Posts: 6826 | Location: Satellite Beach,fl,usa | Registered: March 02, 2001Reply With QuoteEdit or Delete MessageReport This Post
Posted Hide Post
Tom, what is a shoulder clod?
 
Posts: 263 | Location: Healdsburg, CA | Registered: June 22, 2004Reply With QuoteEdit or Delete MessageReport This Post
Tom
Posted Hide Post
Basically it is the 22-24 lb piece of shoulder that a meat cutter reduces to chuck roasts.
 
Posts: 6826 | Location: Satellite Beach,fl,usa | Registered: March 02, 2001Reply With QuoteEdit or Delete MessageReport This Post
Posted Hide Post
The clod I did had excellent flavor, but I couldn't pull it.

I put it in with pork shoulders so I think it went 16-18 hrs @225 and finished @ 275.

I bagged mine into 1# packages and reheat it in a fry pan with butter.

It was off a Red Angus and yielded 54%
 
Posts: 321 | Location: Mankato, Minnesota | Registered: May 10, 2004Reply With QuoteEdit or Delete MessageReport This Post
Posted Hide Post
Is a shoulder clod the same cut as a chuck roll?
 
Posts: 37 | Location: Oregon | Registered: August 13, 2004Reply With QuoteEdit or Delete MessageReport This Post
Tom
Posted Hide Post
Not exactly.

This might help.

Shoulder/chuck cuts
 
Posts: 6826 | Location: Satellite Beach,fl,usa | Registered: March 02, 2001Reply With QuoteEdit or Delete MessageReport This Post
Posted Hide Post
Tom, have to say I sure appreciate all the different website locations that you put on the forum.
Steve.
 
Posts: 115 | Location: Taiwan | Registered: October 31, 2004Reply With QuoteEdit or Delete MessageReport This Post
Tom
Posted Hide Post
Yessir
 
Posts: 6826 | Location: Satellite Beach,fl,usa | Registered: March 02, 2001Reply With QuoteEdit or Delete MessageReport This Post
 Previous Topic | Next Topic powered by eve community  
 


Copyright Cookshack, Inc. 2001 - 2007