I have an FEC 120 IQ4. The temperature on the display fluctuates by over 10f in less than 10 minutes, which seems a bit odd, and a bit fast for to be actually changing. I am going to put in a probe this weekend near the cookshack thermometer to check it.Read More...

Hi Guys, new member here. I’ve been smoking for a long time on log burner smokers and recently had an opportunity to work on a FEC120. I was pleased with the results and ease of use. I found a used FEC240 for $5000. It seems pretty clean. Build in 2013. Tha question is - is it worth it or should I save for a new one? Also if I buy used what is the most expensive part to replace? TIARead More...

Anyone seen a chicken throne made of clay? It is a one piece item and the throne portion holds liquid in the same fashion as a beer can would in a wire throne. The bottom holds drippings like placing a pie pan under a wire throne.Read More...

I own a pg 1000 that was manufactured in late 2021. After about 6 or 7 cooks the hood started to loosen up and had more side to side movement when I open the hood. Seems like the weakness is in the way the hood is made in the front corners. Was wondering if anyone else has had this issue and what can I do to fix it? I did see the newer models have more rivets on the front under part of hood (flat piece that below the handle towards the front of hood when open). Would adding another rivet...Read More...

I’ve purchased one of the above smokers from a site second hand I’m struggling to get it up to temperature they said it was working before I purchased it it gets up to 76f but no further I’ve left it on for 5 hours it’s set on the preset number 1 so 6 hours smoke the 10 hours cooking max temp 240f any help would be much appreciated thanksRead More...

I have a Pit Boss electric smoker grill and a stand up smoker. I need to know what other equipment is needed to make my own deer sticks with cheese. I see plenty of recipes, but don’t want to start and then not have all I need. I want to “set up” for success the first go round. Thanks for your time and sharing your knowledge.Read More...

I have a relatively new 045.... Seasoned per instructions. I was smoking pork tenderloin with apple wood CHIPS. I (unfortunately) was not near, but the ladies of the house, three of them report a very loud BOOM from the unit. They said it shook the house and there was smoke everywhere, out the door and out the hole. My intrepid wife turned it off, but did not open the door. When I came back 15 minutes later, I could find nothing wrong, so I fired it off again and continued to smoke two...Read More...

Looking to host a large event for 120. Going to cook prime rib and have a couple of questions. 1. Cost will be dinner for $35. What weight of slice should I serve? 2. Thinking of using my La Caja China to do this. Anyone else done a large scale cook of prime rib in one of those? Thank you.Read More...

I need to install a new ignitor in my PG1000. How do I remove the fire pot? My fire pot has two bolts/nuts on top and several Phillip head screws in the front. The front screws will be hard to remove due to the steel wall that divides the cooking chamber. I can’t find a nut driver that will work on the two bolts on top. I have many socket and nut drivers but none seem to fit. If anyone knows that size let me know.Read More...

Anyone here have a suggestion for a new home use vacuum sealer?Read More...

Hi, I have a FEC 100 built in 2008. I recently upgraded the controller and have had good results. Today I noticed my auger motor sounding like it was straining. This went on for a few minutes then stopped. I was also experiencing temp fluctuation. I just got back from sitting with it for 20 minutes and it did not make the noise. Does anyone have an idea what might be going on? Thanks, MattRead More...

Hey guys .. what have you all done to raise the level of the Smoker to make it easier to look inside without bending or stooping .. Could you post your pictures of what you have built or used .. since then all of us could take a look at what others have done .. I saw that cookshack is selling a stand .. does any one know if it�s waterproof .. since I would love to leave my smoker outside instead of lugging it in and out of the garage � and I would not want the items inside to get wet ..Read More...

Hey everyone, I am pretty new to smoking and just got my Cookshack smoker. Super excited to dive in but I am a bit nervous about doing chicken for the first time. I have read that it can dry out quickly so I want to make sure I get it right. Any tips on things like temperature, wood choice or seasoning? Should I brine the chicken beforehand, or is that overkill?? Also do you prefer to go low and slow or crank the heat up a bit to get the skin crispy? As well, I found these resources when...Read More...

I have a smoker that is tripping my breakers. I know it says to use a non gfi outlet and run it for a while since the element might have been wet, however, we have all gfi outlets for the entire house. Any other suggestion?Read More...

I did two pork shoulders today. I did them hot and fast method. They came out very nicely. Took about 5 hours total. This was a) my first cook on my FEC 100, and b) my first hot and fast on pork shoulders. My weird experiences were that the internal probe registered 71 degrees for well over an hour from the moment I put it in the meat. I know it was colder in the meat than that at first. But it finally got working a couple of hours into the cook. The other strange thing is all the ash that...Read More...

Had one from a hardware store but it has worn out it's welcome. Any ideas?Read More...

The other day I decided to do a rack of St. Louis spares. Just for grins I looked in my notes about my previous smokes. I discovered that I had started with Smokin’ Okie's 101 on how to do ribs then some time in the years following I have moved to just throwing them into the smoker bone side down, until done 4- 6 hrs. here at 7200 ft. I smoke at 225 deg. with a chunk of cherry or apple depending on my mood. So, I decided to give the 101 a try that is: 2 hrs. bone side up flip and spritz with...Read More...

Hey y'all. Anyone on here using the SM360 to smoke salmon? Trying to use ours to make some hot smoked and having a little trouble getting that deep red/orange/brown color without drying out the outside. Would love any reccomendations.Read More...

Food / Beverage menu about 90% finished. Rest of food menu will be completed once we move into actual kitchen. I'm sure a few items will change, plus we'll update/change after 60-90 days. This menu has the ability to be printed/updated couple of times per month. Comments welcome. PS. Actual size is 11 x 17Read More...

I am looking at purchasing the SMO45 to hold brisket similar to Goldees. Any experience you can share with me?Read More...

I wanna know in your opinion what smoker and or brand would be best for all year round use. We live in the norther part of the US and get plenty snow and wanted to continue to smoke during those snowy months.Read More...

Hello there, I am new to using my Cookshack smoker and could really use some advice from the seasoned veterans in this community. I recently bought a Cookshack SM025; and I am planning to smoke a beef brisket this weekend for a family gathering. I have had some decent success with ribs and chicken; but brisket feels like a whole new challenge; and I want to make sure I get it just right. When choosing a brisket, do you have any recommendations on the ideal size or cut for smoking in the...Read More...

Hi everyone! I'm finally the very proud owner of a 2009 SM025! I started with a Weber Smokey Mountain 18", then moved to a Traeger, and now I've got the Cookshack. Did the first cook on it this weekend, 3 pack of Costco BB ribs. After reading quite a few posts, I settled on 235 temp and a 3oz chunk of apple wood. I'm used to using a 3-2-1 method on ribs, but this time ran them the whole time just on the rib rack, no foil. I check on them at 3.5hrs, and when I opened the door I lost all the...Read More...

My new fec120 was delivered Monday, 9/16. I was so excited and did a test run of a couple racks of Baby Backs that night. Turned out great. I purchased the 120 to cook for a fund raiser to raise money for repairs to an old community center. That’s what I told my wife anyway. I’ve had several fec smokers including a fec750 and are accustomed to large cooks. My mission was to cook 270# of butts and 80 racks of baby backs in two days. The five rib racks that I ordered didn’t get delivered until...Read More...

I have 2 iq5's that i am fixing for a friend that have been in storage for a while. Hank starts up and i can start a cook program, all the fans are going, 240v is going to the ignitor but thats not heating utp. But i have replaced lots of ignitors before, and it is getting 240v. But the auger motor is not moving and i cannot measure any voltage accross it. Can anyone suggest the first place to start? These are my first IQ5's to fix. The 2nd iq5 Patsy she starts, and i can start a program,...Read More...

Do you need to rotate rib racks on a fec120 like you do on a fec100. Cooking 40 rack using 5 rib racksRead More...

Let's get this forum moving again! I'll start... Picked up a nice rack of short ribs at the local store. On sale for $3.99/lb. Gave them a good coat of Tatonka Dust & 407BBQ rub. Into the FEC they go. Two hours at 200 for some extra smoke then up to 250 for the remainder of the smoke. But they were taking a while, so near the end I cranked it up to 350 to get them done. Damn things took close to nine hours. Longest they've ever taken. Usually it's six to seven hours. Never know which way...Read More...

Had done beef ribs a couple times with variable results. Impulse buy at grocery store for some good looking beef back ribs. Came home to read up on the forum and found some folks discouraged beef back ribs due to lack of meat and difficulty removing the membrane. Membrane was difficult to get started but came off relatively easy once it was started. Rubbed with Mccormicks garlic pepper and Butchers premium rub. Same basic combo I use for brisket. Into cold AQ smoker set to 225 with hickory...Read More...

I'm seeing St. Louis ribs being offered in weight categories such as 1.5Lb, 2Lb, 2.5Lb, 3Lb and3.5Lb. I've always thought 2.5Lb was pretty much normal. What would you choose and why? TNX, mmRead More...

Anybody built or had built an outdoor kitchen around a pg500? I'm searching for ideas. Thanks!Read More...

Got a PM asking about Wet Aging and so thought I'd bring it here to discuss as we've got a thread going for Dry Aging. Aging ONLY applies to beef, not chicken or pork Wet aging has really grown in use by Restaurants over the last 10 years for one reason; less waste. WHY? Aging is supposed to intensify the flavors SHOULD I AGE? Ah, good question grasshopper. I find, that the more complicated the recipe the less important it is. If you're going to cover the beef in complicated rubs and sauces...Read More...

I've got to brine a few turkeys next month, I'm thinking the number will turn out to be 150-200 14-15lb'ers. My questions are: 1)What is the minimum time in the brine to get acceptable results? Will 12 hours be enough, or do I need to plan on 24 or more? It would be great if I could more or less match the brine time to the cook time so I can push these turkeys out quick, but quality is my priority. 2)Can I reuse the brine? I'm expecting to do 3-4 batches of turkeys back to back. I could add...Read More...

I’m doing a big cook for the local community center this weekend. Serving 15 butts and 20 racks of St Louis ribs Saturday and again on Sunday. Planning on 5 hours @ 250 for ribs and 12 hours at 250 for butts. Cook times seem reasonable? I’ve got 4 rib racks and planned on 5 ribs per rack. Reasonable? Never used the racks before. I owned a fec100 and are used to rotating the meat. However I bought the fec120 to keep from rotating. Is rotating necessary? Any pointers greatly appreciated ThanksRead More...

I was watching the video below and nooticed that the chicken was put in the smoker without preheat. Is this correct? Doesnt this expose the meat to the "early" smoke which Ive read is more harsh in flavor. I've preheated for all my smokes so far. Thanks for any thoughts. https://www.youtube.com/watch?v=JDovya1Ixs0Read More...

Formerly used a Big Chief for smoking brined salmon. At 65F ambient, interior temperature would max out at 165F. Technique was to use three pans of alder chips (2 hours smoking) and then 3-4 hours with no smoke to finish drying process. Perfect results. Have never been able to duplicate this in my SM066. Temperature is hit in about 40 minutes and smoke stops. Results at 5-6 hours has same doneness and little smoke flavor. I've tried the cold smoke baffle (no ice) and get about an hour of...Read More...

How many butts can you cook in a FEC120? I need to cook 16 butts 2 nights in a row.Read More...

First time for Pork Butt on a CS. What do most people inject their Pork Butt with? Or do you inject at all? Thanks from a new comer. Don BRead More...

Ok, so I thought I did enough homework to justify buying the FEPG over a Traeger Crapco roadshow Chinesium special. Well I am at about 10 cooks in. the FEPG is a good grill above 300 degrees. I can't get it to go low and slow, e.g 170-180. Tried the factory set 10-50, and changed that to 10-30. Got 6o degree overshoots on 170 degress turned some $15/lb wild salmon into Jerky. Low and slow is important to me..... Any suggestions are appreciated. The other problem I have is bridging, Running...Read More...

Has anyone successfully upgraded one of their electric smokers to use an off the shelf available Thermostat controller. I love that I can go as low as 100 deg to do things like jerky etc. But i would also like to go as high as 500 deg so i can use this to bake with. Having the ability to take a pie or any type of baked goods to the next level with some smoke flavor is what I'm looking to achieve. would the heating element need to be upgraded as well?Read More...

I have read several posts about cleaning using the find feature and I see most people suggest cleaning with Greased Lighting. I have been using some Simple Green on the exterior just to get my finger smudge marks off and was wondering would this stuff work inside? I keep a 1 part to 10 part water solution in a spray bottle and it works wonders on the outside. I am 8 smokes in on my new smokette and have only wiped the inside down with paper towels. I have washed the racks every time but...Read More...

I've been playing around with the carnivore diet for about 13 months. It's been pretty good just eating beef, butter, bacon, eggs, and salt. I've dropped 42 pounds and still have a few more to go. In my last post, I took ground beef, eggs, and butter and blended them into a batter and cooked them like pancakes. Very delicious. Tonight, I made carnivore bread. It consist of eggs, egg white powder, gelatin, baking soda, yeast, and heavy cream. It is quite shocking the end results. The bottom...Read More...

I hope this doesn't get me in trouble or banned. ThermoWorks just announced a new product that looks really good. This is a wireless leave in temperature probe. This whole system can run up to 50+ probes on one receiver. You can take a look at them here: RFX Wireless (thermoworks.com) .Read More...

I’ve owned an FEC 750 for several years. It’s been flawless. I went to turn it on this weekend and it wouldn’t get hot. Opened the firebox to see what was going on, and discovered there were no pellets in the fire pot. Come to find out the augers weren’t getting power. No, they’re not jammed with wet pellets. Yes the fans, igniters, and rotisserie motor is working fine. I called cook shack and was told how to reset the IQ5 board. Still no power to the augers. There’s an LED panel on the...Read More...

Humor me by listening to my long tale of woe. I started smoking sausage severl years ago with a WSM - could not learn to control temperature, and smoking sausage was a failure. Purchased a MES and experienced the same overshoot of temperatures and fat out sausages. Gave up, but kept my Weber for grilling. Purchased a RecTeq RT-1250 pellet grill, and it works quite well for low-and-slow cooking, but the lowest temperature setting is 180℉. Too hot for sausage. Now I have a slightly used...Read More...

<accidentally deleted my prior post... so reposting here!> Hi everyone! I've read through every single forum post on baby back ribs and the general consensus seems to be to smoke at either 225F (will take around 4-6 hours) or 250F (will take around 3-5.5 hours) with 2-3 oz wood. Has anyone experimented with both temps, and which did you prefer & why? Also, in case it's helpful for those looking for baby back guidance I've copy and pasted my notes from all of the various members on...Read More...

I decided to have BBE tonight for dinner. I cooked 1 lb. of 80/20 ground beef, 7 eggs, and and about 1/2 stick of butter. I cooked this at 375 degrees per side for 4 minutes. Look how they turned out:Read More...

There has been a spate of inappropriate posts. Some have been adult oriented and resulted in an immediate ban. Some links are just not remotely related to bbq/smoking . I will delete a link on the first occurance and/or ban the poster for plagiarism.. A repeat foreign language link, not to mention gaming and other non bbq/smoking links will result in a ban. If someone wants to post about a piece of related gear - grinder, stuffer, knife for prep and slicing, experience with vacuum sealing...Read More...

I decided to try my first batch of elk/pork summer sauge for some Christmas appetizers. Used Cabelas mix but cut it in half just in case. First step started at 10:30 with door ajar and temp hovered around 90-110 deg. After 1.5 hours my casings were tacky so I added wood and shut the door temp set at 140(lowest setting on smokette). Increased temp every two hours by 10 degree increments. Hit 180 and left alone waiting on the internal to reach 160. Checked temp every two hours all night long...Read More...

Hi everyone, Andrew Hayes here. (professional chef, Brisbane Australia) FEC240(2022) Hello and thank you for this wonderful forum. i have been looking for an overnight brisket method that was suitable for our establishment(lunch times only). and i couldn't find a suitable method on the forum(one that starts their meat just after lunch 3pm ready for next lunch service), so i have spent the last 5 months getting this right and ill post it here. This is a wrap, or no wrap method and the oven...Read More...

In light of the recent posts I decided to share a recent success. I noticed Costco always has whole and sliced pork bellies. I have used the whole ones for bacon but decided to pick up a sliced belly package. I spread them out and dusted both sides of them with the "Right Stuff" from Texas BBQ rub. Straight into a 225 degree smoker on frog mats for 2.5 hours. I never intended on eating them for that night's dinner. I did snack on one and it was delicious. No I had plans for the next night. I...Read More...